kinetikeys-chorder | A wearable , wireless , ergonomic chording keyboard
kandi X-RAY | kinetikeys-chorder Summary
kandi X-RAY | kinetikeys-chorder Summary
kinetikeys-chorder is a C++ library. kinetikeys-chorder has no bugs, it has no vulnerabilities, it has a Permissive License and it has low support. You can download it from GitHub.
Kinetikeys Chorder (aka Kinetikeys-Concept1) is a wearable, wireless, mechanical chording keyboard with one main goal in mind:.
Kinetikeys Chorder (aka Kinetikeys-Concept1) is a wearable, wireless, mechanical chording keyboard with one main goal in mind:.
Support
Quality
Security
License
Reuse
Support
kinetikeys-chorder has a low active ecosystem.
It has 6 star(s) with 0 fork(s). There are 1 watchers for this library.
It had no major release in the last 6 months.
kinetikeys-chorder has no issues reported. There are no pull requests.
It has a neutral sentiment in the developer community.
The latest version of kinetikeys-chorder is current.
Quality
kinetikeys-chorder has no bugs reported.
Security
kinetikeys-chorder has no vulnerabilities reported, and its dependent libraries have no vulnerabilities reported.
License
kinetikeys-chorder is licensed under the MIT License. This license is Permissive.
Permissive licenses have the least restrictions, and you can use them in most projects.
Reuse
kinetikeys-chorder releases are not available. You will need to build from source code and install.
Installation instructions are available. Examples and code snippets are not available.
Top functions reviewed by kandi - BETA
kandi's functional review helps you automatically verify the functionalities of the libraries and avoid rework.
Currently covering the most popular Java, JavaScript and Python libraries. See a Sample of kinetikeys-chorder
Currently covering the most popular Java, JavaScript and Python libraries. See a Sample of kinetikeys-chorder
kinetikeys-chorder Key Features
No Key Features are available at this moment for kinetikeys-chorder.
kinetikeys-chorder Examples and Code Snippets
No Code Snippets are available at this moment for kinetikeys-chorder.
Community Discussions
No Community Discussions are available at this moment for kinetikeys-chorder.Refer to stack overflow page for discussions.
Community Discussions, Code Snippets contain sources that include Stack Exchange Network
Vulnerabilities
No vulnerabilities reported
Install kinetikeys-chorder
Print all the STL files using regular PLA.
Print all the STL files using regular PLA
Solder the terminal block to the microcontroller. If you have a different preference on how to connect the wires to your microcontroller (e.g dupont connectors), go ahead and use that. Ideally don't solder the wires directly to the board. This would allow you to: Reuse the board later on solder the wires to the switches far enough from the PLA
Connect the battery to the microcontroller. Place it nicely under the controller and use screws to connect the microcontroller to the Main Body
Prepare all the 5 switches by attaching 2 wires to each one. In my example, the black wires go directly to the microcontroller pins, and the yellow wires all connect together to ground. I always start with wires a little longer than necessary and trim them before the final connection
Insert all the switches to their designated sockets in the Main Body
For each switch, attach the black wire to the microcontroller and the other one to the joint ground. You could also wire the ground by pasing a single wire from one switch to the other, and then attach the final one to the ground pin, but that would require you to solder very close to the PLA. Solder all 5 ground wires together, or use a 5-wire block connector Connect a single wire from all joined ground wires, to the GND pin on the microcontroller I used pins A0-A4 for the left hand, and pins 9-13 for the right hand. For each hand respectively, these are the pins farther from the switches, giving more wiggle room with the wires
Attach the keycaps to the switches
Use two M2.5 screws to attach the Hand Rest to the Main Body
Put the Hand Strap in water of about 160 degrees F or 70 degrees C for a few seconds until it softens and quickly pull it out of the water and mold around you hand (just the 4 fingers in front of the thumb). It should be snuggly and comfotable, with a firm, yet not tight grip.
Attach the Hand Strap to the Hand Rest using 2 screws, washers and flush nuts
Attach the Cover (note: I need to redesign the way it connects to the main body. In the meanwhile, use some additional adhesive tape to secure it to place.
Wrap the hand-strap in adhesive tape so that it feels nicer and more secure on your hand
Flash the firmware (It's an Arduino-compatible PlatformIO project.
Print all the STL files using regular PLA
Solder the terminal block to the microcontroller. If you have a different preference on how to connect the wires to your microcontroller (e.g dupont connectors), go ahead and use that. Ideally don't solder the wires directly to the board. This would allow you to: Reuse the board later on solder the wires to the switches far enough from the PLA
Connect the battery to the microcontroller. Place it nicely under the controller and use screws to connect the microcontroller to the Main Body
Prepare all the 5 switches by attaching 2 wires to each one. In my example, the black wires go directly to the microcontroller pins, and the yellow wires all connect together to ground. I always start with wires a little longer than necessary and trim them before the final connection
Insert all the switches to their designated sockets in the Main Body
For each switch, attach the black wire to the microcontroller and the other one to the joint ground. You could also wire the ground by pasing a single wire from one switch to the other, and then attach the final one to the ground pin, but that would require you to solder very close to the PLA. Solder all 5 ground wires together, or use a 5-wire block connector Connect a single wire from all joined ground wires, to the GND pin on the microcontroller I used pins A0-A4 for the left hand, and pins 9-13 for the right hand. For each hand respectively, these are the pins farther from the switches, giving more wiggle room with the wires
Attach the keycaps to the switches
Use two M2.5 screws to attach the Hand Rest to the Main Body
Put the Hand Strap in water of about 160 degrees F or 70 degrees C for a few seconds until it softens and quickly pull it out of the water and mold around you hand (just the 4 fingers in front of the thumb). It should be snuggly and comfotable, with a firm, yet not tight grip.
Attach the Hand Strap to the Hand Rest using 2 screws, washers and flush nuts
Attach the Cover (note: I need to redesign the way it connects to the main body. In the meanwhile, use some additional adhesive tape to secure it to place.
Wrap the hand-strap in adhesive tape so that it feels nicer and more secure on your hand
Flash the firmware (It's an Arduino-compatible PlatformIO project.
Support
For any new features, suggestions and bugs create an issue on GitHub.
If you have any questions check and ask questions on community page Stack Overflow .
Find more information at:
Reuse Trending Solutions
Find, review, and download reusable Libraries, Code Snippets, Cloud APIs from over 650 million Knowledge Items
Find more librariesStay Updated
Subscribe to our newsletter for trending solutions and developer bootcamps
Share this Page
