dtc | Device Tree Compiler for Windows

Well, you say you want an average, so AVG seems to be appropriate, and group by UserID:

So Dr. Derek Molly did a really nice job of laying this out and I was able to use the example in his repo. Here is a page he made for explaining how to configure GPIO at boot using Device Tree Overlays: http://derekmolloy.ie/beaglebone/beaglebone-gpio-programming-on-arm-embedded-linux/

Even though his solution is for kernel 3.8 I was able to get the following to compile on 4.19

Solution found:

This is a phandle to the /apb-pclk node elsewhere in the dtb. The "clocks" property is part of the "arm,primecell" binding, documented here: https://www.kernel.org/doc/Documentation/devicetree/bindings/arm/primecell.txt

If an application gets a message in a transacted session, then that message will not be visible to other applications (and hence can't get it). If the application commits the transaction using session.commit() method, then the message is permanently removed from the queue. On the other hand, that message becomes available to other consumers (or to the same consumer) if the message is rolled back by the application.

Another point to note: The AcknowledgeMode parameter in connection.createSession() method has no effect if the first parameter is true - meaning a transacted session is being created. When using transacted session, applications must use commit or rollback methods.

I’ve found how to do it.
For that you should first add CONFIG_ARCH_VEXPRESS and ran ‘make V=1 ARCH=arm64 CROSS_COMPILE=aarch64-none-elf- dtbs |& tee logx’
Dtbs for ARCH_VEXPRESS are generated in the dts directory. Then you can see the command to make the dtb (in the logx file).
Below is the command. Lots of options for the dtc(related to unit address too).

mkdir -p arch/arm64/boot/dts/arm/ ; gcc -E -Wp,-MD,arch/arm64/boot/dts/arm/.fvp-base-revc.dtb.d.pre.tmp -nostdinc -I./scripts/dtc/include-prefixes -undef -D__DTS__ -x assembler-with-cpp -o arch/arm64/boot/dts/arm/.fvp-base-revc.dtb.dts.tmp arch/arm64/boot/dts/arm/fvp-base-revc.dts ; ./scripts/dtc/dtc -O dtb -o arch/arm64/boot/dts/arm/fvp-base-revc.dtb -b 0 -iarch/arm64/boot/dts/arm/ -i./scripts/dtc/include-prefixes -Wno-unit_address_vs_reg -Wno-unit_address_format -Wno-avoid_unnecessary_addr_size -Wno-alias_paths -Wno-graph_child_address -Wno-simple_bus_reg -Wno-unique_unit_address -Wno-pci_device_reg -d arch/arm64/boot/dts/arm/.fvp-base-revc.dtb.d.dtc.tmp arch/arm64/boot/dts/arm/.fvp-base-revc.dtb.dts.tmp ; cat arch/arm64/boot/dts/arm/.fvp-base-revc.dtb.d.pre.tmp arch/arm64/boot/dts/arm/.fvp-base-revc.dtb.d.dtc.tmp > arch/arm64/boot/dts/arm/.fvp-base-revc.dtb.d

You can use this command to make a specific dtb file.

If you have the policy that installed the SharePoint Designer, you have to open group policy management editor, then go to computer/user configuration (depending on which one you used) -> policies-> software settings -> software installation-> there you will have your installed software, right click it, go to properties, now in deployement you have a checkbox "Uninstall this application when it falls out of scope of management" . If you tick it, it will uninstall the application, if the computers/users won't have this policy applied to their group.

If its not installed via GPOI think it would be quite easy to create an installing GPO, apply it and then remove it from the scope of management, I think it should work :)

I see three things here

The first is that when you do $DTC = Get-DesktopCount, what happens is you're saving the result of Get-DesktopCount as $DTC. No matter how many desktops you create or remove, the value stored in $DTC has already been set and will not update until you tell it to change.

The second is that the loop's condition seems to be backwards - you probably want to keep going Until there are less than 2 desktops (or, While there are more)

Finally, while I don't think it does any harm in this case, I don't think you want to use Do here - by using Do { ... } While ( ... ) instead of While ( ... ) { ... } you end up running the block at least once, even if the condition is false (so you close Desktop 2 at least once, even if there are fewer than 2 desktops)

All in all, I think what you want is probably something closer to