grid | GRID is a collaborative planning and voting tool

In the following histogram,

A part of my form contains QGroupBox (Status Box) with 4 child QGroupBoxes arranged in a grid layout (2x2). Two bottom QGroupBoxes (Widget 1 Box and Widget 2 Box) contain widgets of fixed size (with set minimumSize and maximumSize) so they're non-resizable at all in both directions. Because of that rigid size constraints top row of QGroupBoxes (Summary Box and Helper Box) can only be resized in vertical direction.

And here comes the troublesome part. Top-left QGroupBox (Summary Box) have grid layout 5x3 while top-right (Helper Box) have vertical layout with 6 rows. If I have naive widget placement as shown on picture 1 Qt is enlarging vertical size of both labels in top row to make height of both QGroupBoxes equal (see red arrows on picture 1).

This is definitely that I don't want so I've added vertical spacer to the bottom of Summary Box and from the first glance it worked (picture 2). But only from the first glance... What you see is the minimum height of my whole form and the bottom side of spacer and last QCheckBox in the Helper Box seems to be aligned.

If I'm expanding my form vertically this spacer grows a bit and that causes the increase of height of both top QGroupBoxes. As a result spacing between QCheckBoxes increases too and we can also see that top and bottom spacing are unequal for the top-right box (see red arrows on picture 3).

I've tried to play with sizeType for my vertical spacer. If I set it to Minimum or MinimumExpanding then the spacer doesn't grow on resize (and doesn't shrink, too) but it appears to be expanded to the size as on picture 3 (corrupting spacings between QCheckBoxes too). If I set it to Maximum, Preferred or Expanding then I observe the same behavior as described above for picture 3.

What is the proper way to achieve alignment for two QGroupBoxes in a row of grid without affecting spacing between elements (e. g. in that case make vertical spacer to fit only single row of grid layout and never expand/shrink)?

I am trying to make a page responsive but, I am not able to make an image responsive as it is getting off the grid container in material UI. Is there a way I can make the image responsive? I am trying to add the image in Grid container, Still, it is showing the same.

I have this component that contains a card and inside this card there are elements and I want to separate them through a vertical line and the problem is that the vertical line does not work.

We just got Telerik controls today and I am trying to "switch out" the old controls for the new Kendo UI MVC Controls.

I have a select2 multi-selection dropdownlist and I am trying to send the "selected to paramters through the Kendo UI dataSource to the controller method to return the specific records.

Here is my .cshtml Razor code:

I have two grid setup's

1. Local grid setup (hub and nodes are running in my local machine) and my local machine connected to network#1

2. VM grid setup (hub and nodes are running in my virtual machine) and my virtual machine connected to network#2

When I execute the scripts I need to pass the IP address as a parameter. Here, I can run my scripts successfully in local machine(code is available in local machine) by passing the network#1 IP address but if I pass the network#2 IP address (VM IP address) to local machine then I am getting below exception,

org.openqa.selenium.remote.UnreachableBrowserException: Could not start a new session. Possible causes are invalid address of the remote server or browser start-up failure.

As per my knowledge, hub and nodes should be connected to same network. Cannot we run the scripts by passing the VM IP address to local machine?

Trace:

I want to initialize a structure with an array of string without doing dynamic allocation. Is it possible? I had thought of something like this but it doesn't work:

Good morning,

I am creating an animation by connecting 6 nodes coordinates at 10 different time steps.

I start with a test: I first create a static plot for a time equal to 2 (for example) and I get the exact static plot that I am expecting: all and only the consecutive nodes are connected.

Then I create the animation. Unfortunately, the animated plot connects the nodes in the wrong way. You can see that the animation connects the consecutive nodes, but also the second and the second to last nodes.

Any idea why? Thanks

I am trying to make a popup for messages such as "Action completed" and I want a button on it to close the popup (A simple OK which quits only the popup). It also sometimes moves behind the window which is annoying. I have some code for the button but it has an issue with the geometry of the shape since the shape isn't exactly defined as it is variable through the size of font and text length.