JETI_EX_BUS | A MicroPython implementation of the JETI Ex Bus protocol

by chiefenne Python Version: Current License: MIT

X-Ray Key Features Code Snippets Community Discussions Vulnerabilities Install Support

kandi X-RAY | JETI_EX_BUS Summary

JETI_EX_BUS is a Python library. JETI_EX_BUS has no bugs, it has no vulnerabilities, it has a Permissive License and it has low support. However JETI_EX_BUS build file is not available. You can download it from GitHub.

A MicroPython implementation of the JETI Ex Bus protocol

Support

Quality

Security

License

Reuse

Support

JETI_EX_BUS has a low active ecosystem.

It has 5 star(s) with 1 fork(s). There are 2 watchers for this library.

It had no major release in the last 6 months.

JETI_EX_BUS has no issues reported. There are no pull requests.

It has a neutral sentiment in the developer community.

The latest version of JETI_EX_BUS is current.

Quality

JETI_EX_BUS has 0 bugs and 0 code smells.

Security

JETI_EX_BUS has no vulnerabilities reported, and its dependent libraries have no vulnerabilities reported.

JETI_EX_BUS code analysis shows 0 unresolved vulnerabilities.

There are 0 security hotspots that need review.

License

JETI_EX_BUS is licensed under the MIT License. This license is Permissive.

Permissive licenses have the least restrictions, and you can use them in most projects.

Reuse

JETI_EX_BUS releases are not available. You will need to build from source code and install.

JETI_EX_BUS has no build file. You will be need to create the build yourself to build the component from source.

Installation instructions, examples and code snippets are available.

It has 662 lines of code, 62 functions and 10 files.

It has high code complexity. Code complexity directly impacts maintainability of the code.

Top functions reviewed by kandi - BETA

kandi has reviewed JETI_EX_BUS and discovered the below as its top functions. This is intended to give you an instant insight into JETI_EX_BUS implemented functionality, and help decide if they suit your requirements.

Send an Exbus packet .
Reads compressed data from l3 .
Compose Ex Packet
Save a stream to a file .
Read pressure .
Calculates the CRC of the data .
Initialize the bus .
Calculates the CRC of a given CRC .
Calculate the CRC of a packet .
Log a message

Get all kandi verified functions for this library.

JETI_EX_BUS Key Features

No Key Features are available at this moment for JETI_EX_BUS.

JETI_EX_BUS Examples and Code Snippets

No Code Snippets are available at this moment for JETI_EX_BUS.

Community Discussions

No Community Discussions are available at this moment for JETI_EX_BUS.Refer to stack overflow page for discussions.

Community Discussions, Code Snippets contain sources that include Stack Exchange Network

Vulnerabilities

No vulnerabilities reported

Install JETI_EX_BUS

The following image shows the components and connections as used during the development. The figure below shows how the resistor is soldered at the split point of the wires. It is only active on the wire going to the Y9 pin of the Pyboard. The Pyboard is in a small housing and a Jeti REX6 receiver is attached. The yellow wire (channel 6) splits into two wires (one with a 2.4kOhm resistor as per the Jeti specification) which are connected to TX(Y9) and RX(Y10) on UART(3) on the Pyboard. The black wire establishes a common ground. The receiver is powered by a 4S NiMH accumulator via channel 1. Channel 6 of the receiver was set to "Ex Bus" (see image below) in the device manager of the Jeti transmitter.

Support

For any new features, suggestions and bugs create an issue on GitHub. If you have any questions check and ask questions on community page Stack Overflow .

Find more information at: