gopro-manager | GoPro manager script to accommodate triggered activation
kandi X-RAY | gopro-manager Summary
kandi X-RAY | gopro-manager Summary
gopro-manager is a Python library. gopro-manager has no bugs, it has no vulnerabilities, it has a Permissive License and it has low support. However gopro-manager build file is not available. You can download it from GitHub.
A Python script to manage the activation of multiple GoPros in a race car environment. This script was written for and tested against GoPro Hero 7s (silver and black editions). There are numerous caveats, assumptions and prerequisites so please read all of the documentation prior to trying it out. Huge thanks to the documentation at KonradIT's Github repo.
A Python script to manage the activation of multiple GoPros in a race car environment. This script was written for and tested against GoPro Hero 7s (silver and black editions). There are numerous caveats, assumptions and prerequisites so please read all of the documentation prior to trying it out. Huge thanks to the documentation at KonradIT's Github repo.
Support
Quality
Security
License
Reuse
Support
gopro-manager has a low active ecosystem.
It has 3 star(s) with 0 fork(s). There are 1 watchers for this library.
It had no major release in the last 6 months.
There are 1 open issues and 0 have been closed. There are no pull requests.
It has a neutral sentiment in the developer community.
The latest version of gopro-manager is current.
Quality
gopro-manager has no bugs reported.
Security
gopro-manager has no vulnerabilities reported, and its dependent libraries have no vulnerabilities reported.
License
gopro-manager is licensed under the MIT License. This license is Permissive.
Permissive licenses have the least restrictions, and you can use them in most projects.
Reuse
gopro-manager releases are not available. You will need to build from source code and install.
gopro-manager has no build file. You will be need to create the build yourself to build the component from source.
Installation instructions, examples and code snippets are available.
Top functions reviewed by kandi - BETA
kandi has reviewed gopro-manager and discovered the below as its top functions. This is intended to give you an instant insight into gopro-manager implemented functionality, and help decide if they suit your requirements.
- Start monitoring the GPIO pin
- Power on the device
- Perform a http request using pycurl
- Check if the card is capturing
- Attempt to connect to the server
- Check if wifi is connected
- Power off the device
- Start capture
- Stop capture
- Sudo gatttool write command
- Change ip route
- Add a GoPro
Get all kandi verified functions for this library.
gopro-manager Key Features
No Key Features are available at this moment for gopro-manager.
gopro-manager Examples and Code Snippets
No Code Snippets are available at this moment for gopro-manager.
Community Discussions
No Community Discussions are available at this moment for gopro-manager.Refer to stack overflow page for discussions.
Community Discussions, Code Snippets contain sources that include Stack Exchange Network
Vulnerabilities
No vulnerabilities reported
Install gopro-manager
It's easiest to ensure your wireless connections are active by toggling Wireless Connections off and then on via the onscreen menus, then do a scan on your device with sudo iw wlan0 scan. You'll get a fair amount of output, look for the SSID of your GoPro and look at the top of the entry for the BSS address. That is your wifi address that you can plug in to the config. That's rather up to your OS, but on Raspian, you can edit /etc/network/interfaces to configure each interface to a specific SSID. Just add one of these blocks for each with the correct SSID and WPA key. The allow-hotplug keyword instead of auto will allow systemd to continue booting before the interfaces are up. After you've configured that, you can either restart networking with sudo systemctl restart networking or just reboot.
Install the required system packages. (sudo apt-get update; sudo apt-get install python3 python3-rpi.gpio python3-pycurl wakeonlan)
Determine the Wifi and Bluetooth addresses of your GoPros. This is easier said than done. See below.
Configure your wifi to connect to your GoPros. Also see below.
Clone this checkout somewhere on the device. (e.g. /usr/local/gopro-manager)
Create a configuration file as config.py in that directory. (Copy config.py.example for a base)
Copy or move the gopro-manager.service from the systemd directory into /etc/systemd/system. If you don't use /usr/local/gopro-manager for the checkout location, update that path in the service file. With that in place, you can sudo systemctl daemon-reload; sudo systemctl enable gopro-manager.
Install the required system packages. (sudo apt-get update; sudo apt-get install python3 python3-rpi.gpio python3-pycurl wakeonlan)
Determine the Wifi and Bluetooth addresses of your GoPros. This is easier said than done. See below.
Configure your wifi to connect to your GoPros. Also see below.
Clone this checkout somewhere on the device. (e.g. /usr/local/gopro-manager)
Create a configuration file as config.py in that directory. (Copy config.py.example for a base)
Copy or move the gopro-manager.service from the systemd directory into /etc/systemd/system. If you don't use /usr/local/gopro-manager for the checkout location, update that path in the service file. With that in place, you can sudo systemctl daemon-reload; sudo systemctl enable gopro-manager.
Support
For any new features, suggestions and bugs create an issue on GitHub.
If you have any questions check and ask questions on community page Stack Overflow .
Find more information at:
Reuse Trending Solutions
Find, review, and download reusable Libraries, Code Snippets, Cloud APIs from over 650 million Knowledge Items
Find more librariesStay Updated
Subscribe to our newsletter for trending solutions and developer bootcamps
Share this Page
