nak | The Nak Machine Learning Library | Machine Learning library

First i am a lost noob

I have been recently trying to find out a way weather i can send serial data (large file like image data) only through the Rpi w 0's micro USB port using ttyGS0.but when i searched online i only found ways of setting up headless through serial and other stuff which was no what i wanted. But i did follow the tutorial half way

• I went to '/boot/config.txt' and set 'dtoverlay=dwc2' at the end of the file after leaving a line

• I went to '/boot/cmdline.txt' and did put 'modules-load=dwc2,g_serial' after 'rootwait' leaving a space

Thinking i could just use the /dev/ttyGS0 in my serial program on the Rpi and send the data the data was being sent but on my PC when i tried to access my Rpi which was on comport 12 it said port not found and couldn't open it.But it was showing up in the device manager as 'PI USB to Serial(COM12)'

Then i wondered weather it would be possible at all to access Rpi's comport this way.

If that's the case, i want to know if there is any other way to access the Rpi's USB port only using the USB cable

Note:-

• I don't want to use Rpi's USB as a way of loging ie. 'headless setup'.i just want to receive serial data like an arduino.
• I don't want to use the GPIO pins(i tried) as they can only send limited characters at a time and i want to send an image file. Very quickly.
• I don't have any serial converters at hand so i could route it to the arduino and use /dev/ttyUSB0 then read it on PC. I just only want to use the USB cable.
• In case this info is required:-
  • my pc is a probook 6560b running windows 7

things i found while testing and stuff:-

• I did do -lsusb command but i dint find my device on that list
• I tried the 'ls /dev/ttyGS0' and i found '/dev/ttyGS0'
• I checked many forums and some guys were asiking to use this command 'dmesg | grep tty'and show them the code . So i performed it i dont understand what alot in the piece of text means but if it would be helpfull i pasted it here:-

If I have a constrained link with a theoretical 3s of latency, 300kpbs speed and 400B MTU size for my data, how would I tune uftp given such constraints?

I have tried to use uftp specifying the transmit rate, block size using a fixed size with no congestion control:

I'm trying to test some probes connected via USB on an Linux device using Perl 5.28 and Linux (Debian 8). When I read out a large file buffer of the probe, often none readable ASCII signs occur like \0 or \x02. I want to translate these signs into readable tagged text. I've written a small subroutine, but it seems to me a little bit clunky for large translation list to test every entry. Is there a better way to do that?

Example script

I'm trying to receive stock data for about 1000 stocks, to speed up the process I'm using multiprocessing, unfortunately due to the large amount of stock data I'm trying to receive python as a whole just crashes.

Is there a way to use multiprocessing without python crashing, I understand it would still take some time to do all of the 1000 stocks, but all I need is to do this process as fast as possible.

I'm trying to make a 8 KB replay buffer in Verilog, and when setting up the test-bench and running it, I get undefined states for the output, a high impedance for the ready, and undefined output for the data, as well as an undefined sequence variable. I'm not exactly sure as to how to get the test-bench to display the correct results. I've tried assigning data for the sequence variable, but nothing seems to be working.

My waveform is like this (https://imgur.com/a/hNt1bXU). My reg variables are initialized, and I'm not sure what the issue is in order to get a proper output for the waveform.

Replay Buffer

After Executing This code i am getting error win not found running tkinter from different function is important as its a homework

Code:

I'm using Python 3.7.9. I'm trying to use scapy by adapting the code found in this link (for the credits):

https://cabeggar.github.io/2016/02/21/DHCP-starvation-with-ScaPy/

In the GraphQL API, I often see naming conventions such as NQ and MQ as parameters used in cursor. This is an example, shown below,

After I scraped for the links, I got to the next page but scrapy is not showing the results expected. I think it might be a Xpath problem but when I use scrapy shell it seems to work just fine.

Here is the code: