arduino-ide | repository contains the source code

by arduino TypeScript Version: 2.1.0 License: AGPL-3.0

X-Ray Key Features Code Snippets Community Discussions(5)Vulnerabilities Install Support

kandi X-RAY | arduino-ide Summary

arduino-ide is a TypeScript library typically used in Internet of Things (IoT), Arduino applications. arduino-ide has no bugs, it has no vulnerabilities, it has a Strong Copyleft License and it has medium support. You can download it from GitHub.

This repository contains the source code of the Arduino IDE 2.x, which is currently in beta stage. If you're looking for the stable IDE, go to the repository of the 1.x version at The Arduino IDE 2.x is a major rewrite, sharing no code with the IDE 1.x. It is based on the Theia IDE framework and built with Electron. The backend operations such as compilation and uploading are offloaded to an arduino-cli instance running in daemon mode. This new IDE was developed with the goal of preserving the same interface and user experience of the previous major version in order to provide a frictionless upgrade.

Support

Quality

Security

License

Reuse

Support

arduino-ide has a medium active ecosystem.

It has 1546 star(s) with 270 fork(s). There are 66 watchers for this library.

It had no major release in the last 12 months.

There are 451 open issues and 970 have been closed. On average issues are closed in 198 days. There are 13 open pull requests and 0 closed requests.

It has a neutral sentiment in the developer community.

The latest version of arduino-ide is 2.1.0

Quality

arduino-ide has 0 bugs and 0 code smells.

Security

arduino-ide has no vulnerabilities reported, and its dependent libraries have no vulnerabilities reported.

arduino-ide code analysis shows 0 unresolved vulnerabilities.

There are 0 security hotspots that need review.

License

arduino-ide is licensed under the AGPL-3.0 License. This license is Strong Copyleft.

Strong Copyleft licenses enforce sharing, and you can use them when creating open source projects.

Reuse

arduino-ide releases are available to install and integrate.

Installation instructions are available. Examples and code snippets are not available.

It has 1962 lines of code, 0 functions and 315 files.

It has low code complexity. Code complexity directly impacts maintainability of the code.

Top functions reviewed by kandi - BETA

kandi has reviewed arduino-ide and discovered the below as its top functions. This is intended to give you an instant insight into arduino-ide implemented functionality, and help decide if they suit your requirements.

Copy the build artifacts to the build directory .
Add a zip file to an array .
Generate an artifact name
Collect all dependencies in project
Calculate the hash for the digest of the channels
Generates the template for the ari project .
Compile a file .
Verifies that all the dependencies are installed .
Returns the version number .
Executes a git command .

Get all kandi verified functions for this library.

arduino-ide Key Features

No Key Features are available at this moment for arduino-ide.

arduino-ide Examples and Code Snippets

No Code Snippets are available at this moment for arduino-ide.

Community Discussions

Trending Discussions on arduino-ide

NodeMCU ESP8266 cannot upload sketch - timeout error

AT-Commands from ESP32 to Fanstel BC805M (nRF52805M) not working

Is there a way to dispose an Arduino String() to free memory?

AJAX Script is not working when used in mobile devices

ESP8266 flush program after power lost

QUESTION

NodeMCU ESP8266 cannot upload sketch - timeout error

Asked 2021-Oct-04 at 09:14

Using arduino-cli, the arduino-ide, or directly the esptool.py (from https://github.com/espressif/esptool) I obtain the following error when uploading a simple (correct) sketch.

...

ANSWER

Answered 2021-Oct-04 at 09:14

The problem was that my last apt upgrade updated the kernel from the 5.4.0-86-generic to 5.4.0-88-generic (I checked the update in /var/log/apt/history.log.1.gz). The driver CH341 in 5.4.0-88 is not working properly (the ESP I'm using require CH340G drivers). The solution is to go back to the 5.4.0-86 drivers and in the following I list what I've done.

disconnect any ESP or board connected to any USB. Then test that the CH341 module (which allows the serial communication with the EPS) is loaded. You can use this code to test the correct unload/load of the module in steps 2, 3.

Source https://stackoverflow.com/questions/69433568

QUESTION

AT-Commands from ESP32 to Fanstel BC805M (nRF52805M) not working

Asked 2021-Aug-26 at 17:51

I want to send a simple AT-Command like: AT\r\n from the ESP32 to the Fanstel BC805M (nRF52805M) breakout board. My goal is to get an answer.

Problem: The Esp32 does not get an answer from the BC805M.

Setup Hardware

The ESP32 is connected by usb cable to my Mac.
The ESP32 connects to the BC805M by five cables -> 3V3->VDD, GND->GND, Rx->Tx, Tx->Rx, GPIO32(high)->GPIO04(P004). Rx and Tx from ESP32 are Serial2 (not the Serial0 of the programmer). The P004 pin from BC805M is set to high to enable "command-mode".

Software

The BC805M came already preloaded with The AT commands code.
The ESP32 is flashed by a simple Serial2 write/read arduino code:

...

ANSWER

Answered 2021-Aug-26 at 17:51

The Fanstel support just wrote me that the BC805M Evaluation Board is NOT preloaded with the AT-Command firmware.

Only the BC805M module has it preloaded.

That explains why the AT-Commands did not work.

Source https://stackoverflow.com/questions/68938081

QUESTION

Is there a way to dispose an Arduino String() to free memory?

Asked 2020-Oct-11 at 00:58

Is there a way to dispose an Arduino String-Object, so the memory it uses gets freed up, when the String is not needed anymore?

I didn't find a function in the reference for this, and when I call free(&str), an Exception is thrown.

Thanks in advance for your help. Simon

Edit: I code with the Arduino-IDE, like this

...

ANSWER

Answered 2020-Oct-11 at 00:58

You can use curly braces to make explicit scopes. The C++ standard requires that objects declared in a scope are destroyed when they go out of scope. For objects that manage dynamic memory (such as String) that means the dynamic memory will be released to the system.

Source https://stackoverflow.com/questions/64299592

QUESTION

AJAX Script is not working when used in mobile devices

Asked 2020-Jul-28 at 17:44

I'm currently working on a project involving ESP32 Arduino programming for showing a webpage where users can interact with buttons for activating relays, also I implement an Slider with a short script. Is based on this project: ESP32 Servo Motor Web Server

Works perfectly for my purposes ... except when i try to use the web platform with no internet connection (I use the WiFi ESP32 config.) in my Android phone; I try to use the slider but it doesn't seems to be doing anything, and when i check for my Serial Monitor just looks like im not interacting with the Slider control.

Code:

...

ANSWER

Answered 2020-Jul-28 at 00:14

What i am thinking is that when you visited the site on your laptop your browser cached the file so it would still function without internet. On your phone, your browser never had the chance beacuse you have never visited with WIFI. So if you clear your cache on your laptop it will probbably stop functioning.

Source https://stackoverflow.com/questions/63125258

QUESTION

ESP8266 flush program after power lost

Asked 2020-Apr-11 at 18:15

I program my ESP8266 with a Arduino Uno and this guidance: Programming the ESP8266 With the Arduino IDE in 3 Simple Steps

Wifi connect, Mqtt connect (subscribe, publish, callback) everything works fine and totally like expected.

But after I disconnect the power from the Arduino Board and reconnect to a another V3.3 power source, the ESP8266 behavior is like a complete clean flushed device and nothing happens.

For programming I use this settings (Arduino IDE 1.8.12):

What I am doing wrong here?

EDIT

1.) I try two different ESP8266, and 3 different scretches (1. proved working in the past, 2. simple blink sketch, 3. sketch with my code I need)

2.) the program stops immediately after disconnecting CH_PD from 3.3V

3.) I update the esp8266 board package to the newest version 2.6.3

...

ANSWER

Answered 2020-Apr-11 at 18:15

The main issue here is my bad documentation. After a long time, I found the solution again here: Easiest ESP8266 Tutorial (Using arduino). Like the first time two years ago. In conclusion, I forgot to disconnect GPIO0 from GND after programming.

The correct way after programming is: