bitstream | Bitstream provides bit-level IO functionality

Possible 2 solutions:

• SDK is probably reading settings from an outdated .eclipse folder or an outdated workspace. Try opening SDK with a fresh workspace. If that does not work, remove your $HOME/.eclipse folder.

• Apparently the Vivado SDK is built into Vitis, and you have to load the exported .xsa file into Vitis after launcing Vitis from the Tools tab in your Vivado. If your looking to import an old SDK project into the new Vitis tool, this link might be useful.

Q : "Is it possible _{( to implement PRAM CRCW on consumer processor )} ?"

A :
Let's clarify the facts first. We can agree on what "consumer"-processors are - the most often a COTS term is right this - a Custom-Over-The-Shelf processor, as anyone can go and buy. So is the set of properties of any such COTS hardware, being pre-defined by the silicon structures pre-fabricated "inside" such processor.

On the contrary, the CRCW PRAM term is knowingly & intentionally a highly abstract, ultimately idealised property of any such processor architecture, that can (without having any limits in time or other compromises) Concurrently Read (under any and all levels of parallelism) and also Concurrently Write (under any and all levels of parallelism) from/into any memory location ("address") all at once, adding some additional créme-a-la-créme property, like to performe a sum of all CW-s, before actually storing a such resulting value. Any such physical implementation of these abstract properties, that meets them all under any circumstances, having no exceptions to doing so in full parallel-mode, can be called a CRCW PRAM and never otherwise.

This said, the CRCW PRAM architecture is by far not met, not even being anywhere close to it, in any of the current COTS processor hardware silicon.

Such question is leading, by definition, to actually unachievable wish to have an architecture-A get "implemented" by using an architecture-B (which can never be turned into meeting an architecture-A, even if composing many such COTS processors (as defined) into some interconnected macro-structure, which may turn some of the COTS hardware properties a bit "closer" to the CRCW PRAM, yet at such devastatingly adverse costs or slowness of operations, that such attempts can result but in something ultra-expensive + ultra-power-inefficient + ultra-slow ( being about N^{2 ~ 3} sub-sampled and having a need to artificially "wait" for all the slowest parts for a full-width of the parallelism to get physically completed, if viewed from the macro-structure point of view).

Using any amount of superscalar, M-way pipelined, out of order executing CISC silicon for achieving a macro-structure topological trick just for simulating a "slowed down" CRCW PRAM is IMHO technically not a right way to go ( if we want to enjoy a reasonably practical O( k )-sorting machine ).

If using a current level of QPU processors, we may "somehow" enjoy a constant time QUBO (a single hardware-instruction quantum processor in the current line of the D-WAVE systems' machines ), I would hesitate to consider this corner-case (topologically setup to bear "inital" state and letting The Nature ( the laws of physics ) to "execute" a quantum-annealing "algorithm" to result in a statistical-distribution of results, answering the problem solution in constant time ) a COTS, which it is not, is it?

The trick is to redirect the value of the attribute PixelData to a file stream. With this, the video is loaded in chunks and on demand (i.e. when the attribute is accessed). But you have to create the whole structure explicitly, that is:

• The Pixel Data element
• The Pixel Sequence with...
• ...the offset table
• ...a single item containing the contents of the MPEG file

Code

With ffmpeg, you can use the drop option of the noise bitstream filter.

This will be a lot faster if you do everything a byte at time instead of a bit at a time.

First change the way you store your lookup tables. You should have something like:

PLEASE READ THE WHOLE ANSWER FOR ACTUAL SOLUTION

I think I got it now, though I did not verify whether the image actually works on my Ultra96v2, yet.

I noticed, that the weird path with commata is inside of the boot.bif and system.bif. So the first time I tried to build it, the bif wasnt there, but got created (I assume). The bif was ready then but only had a weird path inside, so I took the makefile (you can find it in debug/sd_card), copied it, and just commented out the line GENERATE_BIF_XSCT_CMD = ${GENERATE_BIF} -xpfm ${XPFM_PATH} -domains ${DOMAINS} -bifpath ${BIF_PATH}.

Then I edited the boot.bif and system.bif and changed the atf,boot, uboot,boot, and dts,boot to just boot, so the BootGen wouldnt look into the directories with the commata anymore, but only the boot-directory which was specified.

Once that was set up, I executed the edited makefile in my console, by going into the sd_card-directory and executing the following command:

Following are some of the options:

• Once you have generated the bitsteam (.bit file) from Vivado/Vitis, run the following command to get a boot image (.bin file): bootgen -image boot.bif -o i boot.bin

• Further, you can also run the following command to split the image to get the bitstream binary bootgen -image boot.bif -split bin -w on -p xc7kxxxx -o i boot.bin

• Else you can set that option in bitstream settings while using Vivado GUI.

• Or you can also try this script.

• You can also check the official Xilinx video for How to Convert Bitstream to Raw Binary Using BootGen

You are using the font-family property to set both the size and font-family of the text1 class. font-family property is used to set the font family only. So, use this

{font:17px Olney,"Trebuchet MS",Tahoma,Arial,"Lucida Sans Unicode","Bitstream Vera Sans","DejaVu Sans",Sans-serif;}

instead of font-family

Or you can specify the font-size and font-family separately like { font-size:17px; font-family:"Trebuchet MS",Tahoma,Arial,"Lucida Sans Unicode","Bitstream Vera Sans","DejaVu Sans",Sans-serif; }

And if you want to set the width of the image to be 50% then you have to provide some width to the parent div of the image.