element | 💦Load test your app using real web browsers | Automation library

I think you should use the no match route approach.

Check this in the documentation.

https://reactrouter.com/docs/en/v6/getting-started/tutorial#adding-a-no-match-route

I ran into the same issue today and came up with the following solution based on this very helpful article by Andrew Luca

In PrivateRoute.js:

This problem has a fun O(n) solution.

If you draw a graph of cumulative sum vs index, then:

The average value in the subarray between any two indexes is the slope of the line between those points on the graph.

The first highest-average-prefix will end at the point that makes the highest angle from 0. The next highest-average-prefix must then have a smaller average, and it will end at the point that makes the highest angle from the first ending. Continuing to the end of the array, we find that...

These segments of highest average are exactly the segments in the upper convex hull of the cumulative sum graph.

Find these segments using the monotone chain algorithm. Since the points are already sorted, it takes O(n) time.

You can use itertools.dropwhile:

I'm not sure what you're using to code, but in order to set it in Android Studio, open the manifest of your project and under the "activity" section, put android:exported="true"(or false if that is what you prefer). I have attached an example.

there could be at least one difference - case when you need to pass variable to some other function, for example:

It looks like GCC's naïveté about store-forwarding stalls is hurting its auto-vectorization strategy here. See also Store forwarding by example for some practical benchmarks on Intel with hardware performance counters, and What are the costs of failed store-to-load forwarding on x86? Also Agner Fog's x86 optimization guides.

(gcc -O3 enables -ftree-vectorize and a few other options not included by -O2, e.g. if-conversion to branchless cmov, which is another way -O3 can hurt with data patterns GCC didn't expect. By comparison, Clang enables auto-vectorization even at -O2, although some of its optimizations are still only on at -O3.)

It's doing 64-bit loads (and branching to store or not) on pairs of ints. This means, if we swapped the last iteration, this load comes half from that store, half from fresh memory, so we get a store-forwarding stall after every swap. But bubble sort often has long chains of swapping every iteration as an element bubbles far, so this is really bad.

(Bubble sort is bad in general, especially if implemented naively without keeping the previous iteration's second element around in a register. It can be interesting to analyze the asm details of exactly why it sucks, so it is fair enough for wanting to try.)

Anyway, this is pretty clearly an anti-optimization you should report on GCC Bugzilla with the "missed-optimization" keyword. Scalar loads are cheap, and store-forwarding stalls are costly. (Can modern x86 implementations store-forward from more than one prior store? no, nor can microarchitectures other than in-order Atom efficiently load when it partially overlaps with one previous store, and partially from data that has to come from the L1d cache.)

Even better would be to keep buf[x+1] in a register and use it as buf[x] in the next iteration, avoiding a store and load. (Like good hand-written asm bubble sort examples, a few of which exist on Stack Overflow.)

If it wasn't for the store-forwarding stalls (which AFAIK GCC doesn't know about in its cost model), this strategy might be about break-even. SSE 4.1 for a branchless pmind / pmaxd comparator might be interesting, but that would mean always storing and the C source doesn't do that.

If this strategy of double-width load had any merit, it would be better implemented with pure integer on a 64-bit machine like x86-64, where you can operate on just the low 32 bits with garbage (or valuable data) in the upper half. E.g.,

Note: When referring to documentation and source code, I provide links to an unofficial GitHub mirror of R's official Subversion repository. The links are bound to commit 97b6424 in the GitHub repo, which maps to revision 81461 in the Subversion repo (the latest at the time of this edit).

substitute is a "special" whose arguments are not evaluated (doc).

Ok, so I don't know if it is the correct answer, but finally changing the settings in Eslint helped me to change the type of function for Components. I added the following rule to my .eslintrc.js file: